Intramedullary Screw Fixation of Metacarpal and Phalangeal Fractures.

Metacarpal and phalangeal fractures are the second and third most common hand and wrist fractures seen in the emergency department. There are a multitude of operative fixation methods for metacarpal and phalangeal fractures, including closed reduction percutaneous pinning, open reduction internal fixation, external fixation, and intramedullary screw fixation. Although intramedullary fixation is a relatively new surgical technique, it is gaining in popularity as it allows patients to resume range of motion early in the postoperative period with excellent clinical outcomes.

Staple Fixation in Ulnar-Shortening Osteotomies.

Ulnar-sided wrist pain is commonly caused by the ulnar impaction syndrome. Ulnar-shortening osteotomy is a surgical treatment that is used to address ulnar impaction syndrome that fails conservative management. Unfortunately, hardware irritation and nonunion are well-known complications of this procedure. This case report details the course of two patients with nonunion after ulnar-shortening osteotomy who were treated with a combination of a nitinol compression staple and neutralization plate. Further investigation is required to determine the long-term outcomes and indications for nitinol-staple fixation for nonunion after ulnar-shortening osteotomy.

Fixation Techniques for Scaphoid Nonunion.

Scaphoid fractures are common injuries with high risk of nonunion. Various fixation techniques exist for managing scaphoid nonunions, including Kirschner wires, single or dual headless compression screws, combination fixation techniques, volar plating, and compressive staple fixation. The indication for each fixation technique varies depending on the patient, type of nonunion, and clinical scenario.

Ideal Length and Diameter for Intramedullary Screw Fixation of Metacarpal Fractures: A Biomechanical Study.

Purpose: This biomechanical study evaluated the effect of intramedullary screw diameter and length relative to 3-point bending force and torsional force when used to stabilize metacarpal shaft fractures. Methods: Transverse osteotomies were made in the proximal metacarpal shaft in 36 middle finger metacarpal fourth-generation composite Sawbones. To compare screw diameters, antegrade intramedullary screws of 30-mm length were placed in 6 metacarpals, which included 4.7-mm Acutrak 2, Standard Acutrak 2 (4.0 mm), and Mini-Acutrak 2 (3.5 mm) screws. To compare screw lengths, metacarpals were fixated with Standard Acutrak 2 screws of 26, 30, or 34 mm in length, with screw tips bypassing the osteotomy by 6, 10, or 14 mm, respectively. A 6 degrees of freedom robot was used for torsional and 3-point bending testing. Results: Increasing screw diameter demonstrated significant differences in both 3-point bending and torsional strengths. Maximum torsional loads were 69 Ncm (4.7-mm Acutrak 2), 45 Ncm (Standard Acutrak 2), and 27 Ncm (Mini-Acutrak 2) (P < .05). Loads to failure in the 3-point bending tests were 916 N (4.7-mm Acutrak 2), 713 N (Standard Acutrak 2), and 284 N (Mini-Acutrak 2) (P < .05). Differing screw lengths demonstrated significant differences with maximum torsional loads when comparing the 26-mm screws (22 Ncm) with 30- and 34-mm screws (45 and 55 Ncm, respectively) (P < .05). The 3-point dorsal bending strengths were significantly different between the 26-mm screws (320 N) and 30- and 34-mm screws (713 N and 702 N, respectively) (P < .05). Conclusions: The results demonstrated significantly higher torsional strength and resistance to 3-point bending with larger intramedullary screw diameters. Further, when selecting the intramedullary screw length, the screw tip should pass at least 10 mm beyond the fracture. Clinical Relevance: This study provided biomechanical evidence to guide surgeons in selecting intramedullary screw diameter and length for treating metacarpal fractures.

Biomechanics of Proximal Hamate Autograft in Scaphoid Nonunion.

Purpose Treatment of proximal scaphoid fractures remains a challenge with a risk of nonunions and avascular necrosis due to its retrograde blood supply. The ipsilateral proximal hamate has been described as a viable autograft option for osteochondral reconstruction of the proximal scaphoid. Our study evaluated the changes in the contact area and pressure of the radioscaphoid joint after proximal hamate autograft reconstruction. Methods Thin sensors (Tekscan Inc., Boston, MA) were placed in the radiocarpal joints of six fresh-frozen cadaveric forearms. Each specimen's tendons were loaded to 150 N in neutral, 45-degree flexion/extension positions through five cycles. Through a dorsal wrist approach, the proximal 10 mm of the scaphoid and hamate was excised. The proximal hamate autograft was affixed to the scaphoid with K-wires. Peak contact pressures and areas at the scaphoid facet were determined and averaged across loading cycles. Results At the radioscaphoid facet, peak contact pressures were equivalent, although an increasing trend in the neutral and extended wrist position was seen. At the radiolunate facet, contact pressure had an increasing trend in the hamate reconstructed wrists in all wrist positions. Contact areas had a decreasing trend and were nonequivalent at the radioscaphoid facet in the hamate reconstructed wrist. Conclusion After hamate autograft, the contact areas were not equivalent between the native and reconstructed wrists but contact pressures were equivalent in the facets. The proximal hamate has a more pointed morphology compared with the proximal scaphoid, which would explain the change in contact area in the hamate autografted wrist. Our study suggests hamate autograft may present a viable reconstruction for the proximal pole of the scaphoid without significantly altering peak contact pressures at the radioscaphoid facet.

A Morphometric Analysis of Hamate Autograft for Proximal Scaphoid Reconstruction.

Objective Recently, authors have investigated using the proximal hamate as osteochondral autograft for proximal pole scaphoid reconstruction in the case of nonunion with avascular necrosis. The aim of our study was to analyze the morphology and anatomic fit of the proximal hamate compared with the proximal pole of the scaphoid using cadaveric specimens. Materials and Methods Ten cadaver specimens (five males and five females) were dissected. Scaphoid and proximal hamate bones were measured by two independent investigators using electronic calipers and radius of curvature gauges. After measurements were determined to have good correlation, the average value of the two observers' measurements were used for further analysis. Sagittal radius of curvature (ROC), coronal ROC, depth, width, and maximum graft length were compared. Results The average depth of the scaphoid proximal pole was 12.3 mm (standard deviation [SD] = 1.12) compared with 11.3 mm (SD = 1.24) for the proximal hamate ( p = 0.36). The average width was 7.8 mm (SD = 1.00) in the scaphoids compared with 8.6 (SD = 1.05) in the hamates ( p = 0.09). There was also no significant difference in the sagittal ROC between hamates (9.1 mm, SD = 1.13) and scaphoids (9.5 mm, SD = 0.84; p = 0.36). All of these average measurements were within 1 mm. There was a significant difference between the coronal ROC of the hamate (23.4 mm) and scaphoid (21.1 mm) bones in our samples ( p = 0.03). Females were on average smaller than their males, but there was no significant difference in fit based on sex alone. Conclusion The proximal pole of the hamate has similar morphology and size as the scaphoid, with similar depth, width, and sagittal ROC. It has potential as an osteochondral autograft for proximal pole scaphoid reconstruction.

An Anatomical Study of Metacarpal Morphology Utilizing CT Scans: Evaluating Parameters for Antegrade Intramedullary Compression Screw Fixation of Metacarpal Fractures.

PURPOSE: This study evaluated metacarpal morphology for antegrade placement of intramedullary headless compression screws (IMHCS) for metacarpal fracture fixation. METHODS: We analyzed 100 hand computed tomography scans to quantify cortical thickness, intramedullary diameter, and metacarpal lengths. In addition, dorsal or ulnar overhang of the metacarpals over their respective carpal bones was measured. We also predicted optimal entry points for guidewire placement at the metacarpal head. RESULTS: The ring finger metacarpal had the narrowest medullary canal width (coronal, 2.8 mm; sagittal, 3.5 mm). Not counting the thumb, the little finger metacarpal had the widest midshaft medullary width of 4.1 mm in the coronal plane and the middle metacarpal was widest in the sagittal plane with canal width of 3.9 mm. On average, there was maximal dorsal overhang at the base of the middle metacarpal (4.2 mm) and maximal ulnar overhang at the base of the small metacarpal (3.9 mm). The optimal entry point for guidewire placement over each metacarpal head was approximately 3.5 to 3.8 mm volar to the dorsal cortex. CONCLUSIONS: Minimum IMHCS diameters of 3.5 mm for the ring and 4.0 mm for the index, middle and little fingers are necessary to achieve interference fit within the medullary canal. Minimum screw lengths of 38 mm would be needed to ensure 6 mm fixation past the midshaft of the metacarpals. Antegrade IMHCS for fixation of proximal metacarpal fractures may be most feasible with thumb, middle, and little finger metacarpals because there was larger dorsal or ulnar overhang to allow screw placement without violating the carpometacarpal joints. CLINICAL RELEVANCE: Our analysis provides a reference guide for intramedullary screw sizes for each metacarpal of the hand to achieve interference fit with fracture fixation. Furthermore, the dorsal and ulnar overhangs of the metacarpal bases suggest the practicality of antegrade IMHCS fixation.

Evaluation of Antegrade Intramedullary Compression Screw Fixation of Metacarpal Shaft Fractures in a Cadaver Model.

PURPOSE: Surgical options for displaced metacarpal shaft fractures include the use of Kirschner wires, plates and screws, and most recently, intramedullary headless compression screws (IMHCS), which have been reported using only retrograde insertion through the metacarpal head. We evaluated IMHCS fixation of metacarpal shaft fractures through an antegrade approach in a cadaver model. METHODS: We performed antegrade placement of IMHCS in 10 cadaver hands including all 5 digits (total of 50). Displaced transverse proximal metacarpal shaft fractures were created and reduced with a retrograde guidewire from the metacarpal head across the shaft fracture and exiting the metacarpal base. This was retrieved through a 6-mm dorsal wrist incision and overdrilled before the placement of a 4.1-mm-diameter IMHCS in the ring finger and a 4.7-mm screw in all other metacarpals. After IMHCS placement, carpometacarpal (CMC) joint violation was measured along with the optimal starting point for the guidewire on the metacarpal head relative to the dorsal cortex. RESULTS: In all 50 metacarpals, we achieved successful fracture reduction and fixation without violating the extensor mechanism at the wrist. Our retrograde guidewire entry point through the metacarpal head ranged from 4.2 to 4.7 mm volar to the dorsal cortex. The actual area of CMC joint violated by IMHCS placement was largest in the index CMC joint (4.9%), followed by the middle (3.7%), little (2.9%), ring (0.5%), and thumb joints (0.2%). CONCLUSIONS: Placement of IMHCS through an antegrade approach from the CMC joint can be performed effectively for all transverse metacarpal fractures, including the thumb, using a limited incision. There is minimal violation of the articular surfaces of the trapezium, capitate, and hamate for the thumb, middle, ring, and little metacarpals. CLINICAL RELEVANCE: Antegrade IMHCS fixation successfully avoids the potential morbidity of creating a metacarpal head articular surface or extensor mechanism defect at the metacarpophalangeal joint seen with the retrograde approaches.

Risk factors associated with periprosthetic joint infection after total elbow arthroplasty.

BACKGROUND: For patients undergoing total elbow arthroplasty (TEA), the present study aimed to investigate: (i) what risk factors are associated with periprosthetic elbow infection; (ii) what is the incidence of infection after TEA; and (iii) what is the acuity with which these infections present? METHODS: The Statewide Planning and Research Cooperative System database was used to identify all patients who underwent TEA between 2003 and 2012 in New York State. Admissions for prosthetic joint infection (PJI) were identified using ICD-9 (International Classification of Diseases, Ninth Revision, Clinical Modification) diagnosis code 996.66. Multivariate analysis was used to determine risk factors that were independently prognostic for PJI. RESULTS: Significant risk factors for PJI included hypothyroidism [odds ratio (OR) = 2.04; p = 0.045], tobacco use disorder (OR = 3.39; p = 0.003) and rheumatoid arthritis (OR = 3.31; p < 0.001). Among the 1452 patients in the study period who underwent TEA, 3.7% (n = 54) were admitted postoperatively for PJI. There were 30 (56%) early infections, 17 (31%) delayed infections and seven (13%) late infections. CONCLUSIONS: Pre-operative optimization of thyroid function, smoking cessation and management of rheumatoid disease may be considered in surgical candidates for TEA. The results of the present study add prognostic data to the literature that may be helpful with patient selection and risk profile analysis. LEVEL OF EVIDENCE: Level III: prognostic study.

The Quantitative Anatomy of the Dorsal Scapholunate Interosseous Ligament.

BACKGROUND: The anatomy of the scapholunate interosseous ligament (SLIL) has been described qualitatively in great detail, with recognition of the dorsal component's importance for carpal stability. The purpose of this study was to define the quantitative anatomy of the dorsal SLIL and to assess the use of high-frequency ultrasound to image the dorsal SLIL. METHODS: We used high-frequency ultrasound imaging to evaluate 40 wrists in 20 volunteers and recorded the radial-ulnar (length) and dorsal-volar (thickness) dimensions of the dorsal SLIL and the dimensions of the scapholunate interval. We assessed the use of high-frequency ultrasound by comparing the length and thickness of the dorsal SLIL on ultrasound evaluation and open dissection of 12 cadaveric wrists. Student's t test was used to assess the relationship between measurements obtained on cadaver ultrasound and open dissection. RESULTS: In the volunteer wrists, the mean dorsal SLIL length was 7.5 ± 1.4 mm and thickness was 1.8 ± 0.4 mm; the mean scapholunate interval was 5.0 mm dorsally and 2.5 mm centrally. In the cadaver wrists, there was no difference in dorsal SLIL length or thickness between ultrasound and open dissection. CONCLUSIONS: The dorsal SLIL is approximately 7.5 mm long and 1.8 mm thick. These parameters may be useful in treatment of SLIL injuries to restore the native anatomy. High-frequency ultrasound is a useful imaging technique to assess the dorsal SLIL, although further study is needed to assess the use of high-frequency ultrasound in detection of SLIL pathology.

Variations in Hook of Hamate Morphology: A Cadaveric Analysis.

PURPOSE: The hook of the hamate is an anatomical structure that separates the ulnar border of the carpal tunnel from Guyon's canal and serves as a landmark for surgeons. The hook of the hamate is also subject to fracture from injury. We hypothesize that there are variations in the hook of the hamate in the general population. METHODS: One thousand pairs of hamates (2,000 hamates) from the Hamann-Todd Collection at the Cleveland Natural History Museum were analyzed. The height of the hook of the hamate and the total height of the hamate bone were measured using digital calipers. The hook height ratio was defined as the hook height divided by the total height of the hamate. Statistical analysis was performed using unpaired Student's t test to determine differences in sex and race. RESULTS: The mean hook height was 9.8 ± 1.4 mm (range, 2.5-15.9 mm), whereas the mean hook height ratio was 0.42 ± 0.04 (range, 0.15-0.56). There was a 3.1% (62/2,000) incidence of abnormally small hooks, which we classified as hypoplastic and aplastic. Of the hypoplastic hooks, 55% (24/44) were bilateral, whereas 44% (8/18) of the aplastic hooks were bilateral. The incidence of variation in size in the hook of the hamate was highest in white females (9.3%) and lowest in black males (1.4%). CONCLUSIONS: Abnormalities in hook of hamate anatomy are common in the general population, especially in white females. CLINICAL RELEVANCE: Knowledge of anatomic variation in the hook of the hamate may provide additional insight into surgeons' palpation of bony anatomy, interpretation of imaging studies, and use of the hook as a landmark during surgery.

Changes in Provider Treatment Patterns for Dupuytren's Contracture: Analysis of Trends in Medicare Beneficiaries.

BACKGROUND: Collagenase Clostridium histolyticum (CCH) injection has been shown to be a safe and effective treatment option for Dupuytren's contracture. We hypothesize that the gaining popularity of CCH has resulted in a change in treatment patterns among providers, with increased utilization of CCH injections in the management of Dupuytren's contracture from 2012 to 2014. METHODS: The Medicare Provider Utilization and Payment Data Public Use Files were used to identify all surgeons who submitted claims for surgical fasciectomy, needle aponeurotomy (NA), and CCH injection. The data were analyzed for number of providers performing the procedures, number of procedures per provider, and location of practice. RESULTS: From 2012 to 2014, the number of providers performing more than 10 open fasciectomies decreased from 141 to 131. In the same time, the number of providers performing more than 10 NAs increased from 63 to 70 with mean procedures per provider decreasing from 35 to 21. In contrast, the number of providers performing more than 10 CCH injections increased from 72 to 112, with mean injections per provider going from 24 to 20. The total number of injections performed increased from 1,734 to 2,220 from 2012 to 2014. The largest increase in number of injections and number of providers performing injections occurred in the South. CONCLUSIONS: The introduction of collagenase has changed treatment patterns with more providers treating Dupuytren's contractures with CCH injections and a statistically significant decline in the number of NA procedures per provider.

Biomechanical Assessment of the Dorsal Spanning Bridge Plate in Distal Radius Fracture Fixation: Implications for Immediate Weight-Bearing.

BACKGROUND: The goal of this study was to compare the biomechanical stability of a 2.4-mm dorsal spanning bridge plate with a volar locking plate (VLP) in a distal radius fracture model, during simulated crutch weight-bearing. METHODS: Five paired cadaveric forearms were tested. A 1-cm dorsal wedge osteotomy was created to simulate an unstable distal radius fracture with dorsal comminution. Fractures were fixed with a VLP or a dorsal bridge plate (DBP). Specimens were mounted to a crutch handle, and optical motion-tracking sensors were attached to the proximal and distal segments. Specimens were loaded in compression at 1 mm/s on a servohydraulic test frame until failure, defined as 2 mm of gap site displacement. RESULTS: The VLP construct was significantly more stable to axial load in a crutch weight-bearing model compared with the DBP plate (VLP: 493 N vs DBP: 332 N). Stiffness was higher in the VLP constructs, but this was not statistically significant (VLP: 51.4 N/mm vs DBP: 32.4 N/mm). With the crutch weight-bearing model, DBP failed consistently with wrist flexion and plate bending, whereas VLP failed with axial compression at the fracture site and dorsal collapse. CONCLUSIONS: Dorsal spanning bridge plating is effective as an internal spanning fixator in treating highly comminuted intra-articular distal radius fracture and prevents axial collapse at the radiocarpal joint. However, bridge plating may not offer advantages in early weight-bearing or transfer in polytrauma patients, with less axial stability in our crutch weight-bearing model compared with volar plating. A stiffer 3.5-mm DBP or use of a DBP construct without the central holes may be considered for distal radius fractures if the goal is early crutch weight-bearing through the injured extremity.

Complications of Semiconstrained Distal Radioulnar Joint Arthroplasty.

PURPOSE: The Aptis total distal radioulnar joint (DRUJ) prosthesis is a semiconstrained implant designed for treatment of DRUJ arthritis and instability. The purpose of this study was to analyze short-term complications of this device. METHODS: We performed a retrospective chart review of patients undergoing semiconstrained DRUJ arthroplasty from 2007 to 2015 at a single institution. Records were analyzed for complications and the need for subsequent surgical procedures. RESULTS: Two senior hand surgeons at one institution performed 52 semiconstrained DRUJ arthroplasties over 8 years. Nineteen complications necessitating operative management occurred in 15 patients (29%). A total of 26 procedures were undertaken to address these complications. Complications included 4 periprosthetic fractures, 3 infections, 2 instances of aseptic loosening, 2 implant component failures, 1 instance of screw loosening, 3 neuromas requiring neurectomy, 2 instances of finger stiffness necessitating extensor tenolysis, and 2 cases of heterotopic ossification at the DRUJ. Three of the 52 implants were revised (6%) and 2 were explanted (4%); 3 of these (6%) were caused by deep infection. CONCLUSIONS: There is limited literature on outcomes of the semiconstrained DRUJ prosthesis. Prior studies reported low complication rates, with 0% to 5% revisions. In the current clinical series, 29% of patients required further surgery for complications, the most common reasons for which were periprosthetic fracture and infection. TYPE OF STUDY/LEVEL OF EVIDENCE: Therapeutic IV.

Surgical Treatment of Distal Biceps Ruptures.

Distal biceps ruptures occur from eccentric loading of a flexed elbow. Patients treated nonoperatively have substantial loss of strength in elbow flexion and forearm supination. Surgical approaches include 1-incision and 2-incision techniques. Advances in surgical technology have facilitated the popularity of single-incision techniques through a small anterior incision. Recently, there is increased focus on the detailed anatomy of the distal biceps insertion and the importance of anatomic repair in restoring forearm supination strength. Excellent outcomes are expected with early repair of the distal biceps, with restoration of strength and endurance to near-normal levels with minimal to no loss of motion.

Prosthetic Design in Total Wrist Arthroplasty.

Total wrist arthroplasty (TWA) provides a motion-preserving alternative to total wrist arthrodesis for low-demand patients with debilitating pancarpal arthritis. The earlier generation total wrist implants had high complication and failure rates. Advances in prosthetic design have contributed to improved clinical outcomes and implant survivorship. The current fourth-generation implants allow for expansion of indications for TWA. Careful patient selection remains critical; patients with high-demand lifestyles and poor bone stock may not be candidates. Long-term studies on implant survival and patient outcomes are critical for the current generation total wrist implants in assessing their long-term value compared with total wrist arthrodesis.

Limited intercarpal fusion as a salvage procedure for advanced Kienbock disease.

BACKGROUND: With progressive lunate collapse, salvage procedures in advanced Kienbock disease attempt to provide pain relief and maintain motion. Scaphocapitate arthrodesis may provide a durable option with comparable outcomes to proximal row carpectomy in the well-selected patient. METHODS: We performed a retrospective chart review of all consecutive patients with Lichtman stage IIIA or IIIB Kienbock's disease who underwent either scaphocapitate or scaphotrapeziotrapezoid-capitate arthrodesis from January 2004 to December 2013. RESULTS: Twelve patients were included with a mean age of 41.6 years. Ten patients underwent scaphocapitate arthrodesis, while two patients underwent scaphotrapezio-trapezoid-capitate arthrodesis with an average clinical follow-up of 13.1 months. All patients achieved fusion. The average postoperative flexion-extension arc was 53° (range 20-110°). The average ulnar deviation was 9° (range 5-15°), and the average radial deviation was 13° (range 5-25°). Postoperative pain scores were significantly improved, having changed from an average of 6.6 preoperatively to 2.8 on a 10-point scale (W = 18, P < 0.05). CONCLUSIONS: Despite a mean flexion-extension arc that is reduced from that of a normal individual, the postoperative range of motion following a midcarpal arthrodesis was not significantly different than that reported in a recent systematic review of proximal row carpectomy (73.5° compared with 53°, respectively) (P = 0.05). Additionally, given the significant postoperative reduction in associated pain symptoms at the time of follow-up, scaphocapitate arthrodesis should be considered as a treatment option for wrist salvage in the patient with advanced Kienbock's disease.